Velocity Edge GX440 Guide de l'utilisateur Page 172
- Page / 249
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ALEOS 4.2.3 User Guide
172 20080616
Configuring the Remote AirLink Devices for
Modbus with UDP
This section covers standard Modbus settings for the AirLink device at the remote
unit; variations may need additional commands.
1. Configure the ports
In ACEmanager, select Port Configuration in the side menu.
The destination port for the device at the host needs to match the device port in
use on all the devices at the remote sites. For example, if the remote device’s
device port (see below) is “12345”, then the Modbus host device’s S53
destination port should be set to “12345”.
Set the destination port (S53) to match the device port of the host device
(*DPORT). Make sure the device port of the remote device (*DPORT) matches
the destination port of the host device (S53).
Configure IP Addresses for the Host
If the Host device has a static IP address, enter it in the Destination Address for
S53.
Note: With a name instead
of IPs for the host device,
the remote devices will
query the DNS server for
the current IP assigned to
the host device before
sending data back to the
host.
If the device at the host has a dynamic IP and is using Dynamic DNS, instead of
an IP address for S53, specify the name of the host device (*deviceNAME). If the
remote devices are using a different DDNS than the host device, you will need to
specify the fully qualified domain name (*deviceNAME+*DOMAIN).
Note: Setting the Host device IP address as the S53 Destination Address provides a low
level security. The device will not forward UDP traffic unless the source IP/port matches
what is in S53. If you set *AIP=1, however, the device will forward UDP traffic from any
source IP address as long as it is accessing the device on the configured *DPORT.
1. Configure the default mode for start-up.
Each device at the remote locations will need to be configured to communicate
with the device at the host. In ACEmanager, select UDP in the side menu.
a. Enable S82, UDP auto answer.
b. Set S83 to the idle time-out applicable to your application (commonly 20).
2. Configure the other RTU settings.
Other parameters may need to be changed, but this is dependent on the RTU
type being used. At a minimum, this typically involves setting the proper serial
settings to match your RTU.
3. Optional: Dynamic IP Address
If you do not have a static IP, the host device should be configured to report its
current IP to a Dynamic DNS (DDNS) server with Dynamic DNS.
You will need to match the name of the device to the names specified in the host
device’s MLIST or MLISTX for the connected RTU.
- ALEOS 4.2.3 Configuration 1
- User Guide 1
- Trademarks AirCard 4
- Contact 4
- Information 4
- Revision 5
- 6 20080616 6
- Rev 2.3 Feb.12 8 8
- Rev 2.3 Feb.12 9 9
- ALEOS 4.2.3 User Guide 10
- 10 20080616 10
- Contents 11
- Rev 2.3 Feb.12 11 11
- 12 20080616 12
- Rev 2.3 Feb.12 13 13
- 14 20080616 14
- 1: Introduction 15
- 16 20080616 16
- Tools and Reference Documents 17
- 18 20080616 18
- Main Menu Tabs 20
- Configuring 20
- Operation Modes 20
- Telnet/SSH Mode 22
- Creating a Template 23
- Applying a Template 24
- 26 20080616 26
- 3: Status 27
- 28 20080616 28
- WAN/Cellular 29
- 30 20080616 30
- Rev 2.3 Feb.12 31 31
- 32 20080616 32
- Rev 2.3 Feb.12 33 33
- VPN connection has been made 33
- Security 34
- Services 35
- 36 20080616 36
- Applications 38
- Rev 2.3 Feb.12 39 39
- 40 20080616 40
- 4: WAN/Cellular Configuration 41
- 42 20080616 42
- Keepalive 47
- Data Usage Using Keepalive 47
- Re-Activation 48
- 5: LAN Configuration 49
- DHCP/Addressing 50
- LAN Configuration 51
- Rev 2.3 Feb.12 51 51
- Internal DHCP Server 52
- Ethernet 53
- Virtual Ethernet 57
- Virtual Serial 59
- Host Port Routing 62
- Global DNS 63
- 66 20080616 66
- 68 20080616 68
- 6: VPN Configuration 69
- Split Tunnel 70
- VPN Configuration 75
- Rev 2.3 Feb.12 75 75
- SSL Tunnel 76
- Rev 2.3 Feb.12 77 77
- L2TP+IPsec 78
- VPN 2 to VPN 5 82
- 7: Security Configuration 83
- Port Forwarding and DMZ 84
- Port Filtering - Inbound 86
- Port Filtering - Outbound 87
- Trusted IPs - Outbound 89
- MAC Filtering 90
- Packet Inspection 91
- 92 20080616 92
- 8: Services Configuration 93
- ACEmanager 94
- 96 20080616 96
- Configuring Engine Hours 98
- Dynamic DNS 99
- Third Party Services 100
- IP Manager 101
- Understanding Domain Names 102
- Dynamic Names 103
- Control Only 105
- 106 20080616 106
- Gateway Only 107
- Control and Gateway 108
- Trusted Phone Number 111
- Telnet/SSH 112
- Email (SMTP) 113
- Management (SNMP) 114
- Services Configuration 115
- Rev 2.3 Feb.12 115 115
- 116 20080616 116
- • SNMP is disabled 116
- • 65535 116
- Time (SNTP) 117
- 118 20080616 118
- 9: GPS Configuration 119
- Remote Access Protocol (RAP) 120
- Before Configuring GPS 121
- Server 1 122
- Redundant Server 125
- Server 2 to Server 4 126
- Reliability Modes 127
- Local/Streaming 128
- Global Settings 130
- 132 20080616 132
- Introduction 133
- Configuration Overview 135
- Action Description 137
- 138 20080616 138
- Email/SMS 140
- Report Groups 141
- Configure Events 143
- 144 20080616 144
- 11: Serial Configuration 145
- 146 20080616 146
- MODBUS Address List 151
- 152 20080616 152
- 12: Application Configuration 153
- 154 20080616 154
- 13: I/O Configuration 161
- Pulse Count 162
- 14: Admin 163
- Advanced 164
- Radio Passthru 165
- A: Modbus/BSAP Configuration 169
- Modbus TCP/IP 170
- Modbus on UDP 170
- Host for Modbus on UDP 171
- Modbus with UDP 172
- 174 20080616 174
- B: PPP over Ethernet (PPPoE) 175
- Figure B-10: PPPoE Connection 179
- 180 20080616 180
- Figure B-14: PPPoE Connection 181
- 182 20080616 182
- Protocol 183
- SYNTAX DisplayString 188
- 204 20080616 204
- GPS Overview 205
- Configuring the Datum 208
- Over-The-Air (Remote) Host 208
- Local Host 209
- TCP GPS Report Polling 209
- Report Types 209
- Sending Reports Automatically 210
- Store and Forward 210
- RAP Configuration 212
- Device ID 213
- Odometer Data in Reports 213
- I/O Event Reports 214
- NMEA Configuration 215
- Streaming Messages (Local) 216
- TAIP Emulation Configuration 217
- Local Connection 218
- 220 20080616 220
- E: AT Commands 221
- CDMA Info 223
- CPU Status 224
- ATS53=T192.168.100.23/12345 225
- ATS53=foo.earlink.com 225
- ATS53=192.168.100.23/12345 225
- ATS53=/12345 225
- Dynamic IP 232
- PPP/Ethernet 233
- PassThru 234
- Low Power 238
- Firewall 238
- Serial Port 244
- 248 20080616 248
Produits connexes et manuels pour PC/postes de travail Velocity Edge GX440
(127 pages)
(79 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.133 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels